Exactly How to Install a Bathtub in Your Bathroom
Exactly How to Install a Bathtub in Your Bathroom
Blog Article
Listed here below you might get a good deal of brilliant details about A Step-by-Step Guide to Installing a Bathtub.
Mounting a tub isn't specifically rocket science, but it does need strong plumbing, woodworking, and sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a reasonably challenging job. If the old tub is easily easily accessible, the job can relocate rapidly; if you have to open a wall to eliminate the old bathtub and also position the new tub, the task is a lot harder. In either instance, the task is within a residence handyman's skills, although you will need a helper to leave the old tub and also set in the new one. Make sure you have qualified yourself for the job and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you may need a professional plumber to make tube links.
This post will certainly assist you set up a new bathtub in your washroom if you have actually already bought a brand-new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your devices and material list must make up the following:
Preparing for the Installation
Firstly, the sustaining framework supplied with the bath should be fitted (if called for) according to the supplier's directions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make sure that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets unit to prevent pressure on the tub.
Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last position.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, switch on the faucets to drain any type of water staying in the system. The procedure of removing the existing taps can be quite bothersome due to the limited access that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a towel ready for the staying water that will certainly originate from the pipes. When the supply pipelines have actually been gotten rid of, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of both wood boards under its feet, position the bath tub in the required placement. The wood boards are handy in equally spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four small points.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the tub up until the spirit level checks out level.
To set up taps, fit the bottom of the outermost flexible tap connector to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leakages and also tighten them if necessary. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub needs to wait till the bath tub has actually been made use of at the very least once as this will settle it into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin making sure that the washers are in location between the tap and also the sink. Safeguard the faucet in place with the manufacturer supplied backnut. When the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The previous kind should be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and also the tiling, resulting in difficulties with moisture and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes as well as cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly load the tub with water before securing, to permit the motion experienced when the tub is in use. The sealer can crack relatively early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles using waterproof or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on A Step-by-Step Guide to Installing a Bathtub, I was thinking sharing that information was a good thing. Are you aware of another individual who is in to the topic? Why not share it. Kudos for your time. Visit again soon.
Book Maintenance Report this page